Junk It full size 2026

2026 Junk It General Rules

1. These rules apply to every class. Read all rules carefully and follow them! Any questions call or text Nate Burgess 765-744-5524.

2. You must pass inspection within 2 times or you will not run.

3. A 12“ x 12“ roof sign is mandatory.

4. Vehicles must be stock, unless modifications are stated in the rules.

5. A helmet, seat belt, and eye protection must be worn at all times while on the track.

6. If the driver gets out of his or her car for any reason other than an emergency, that driver is considered out, and will not be allowed back in.

7. Any controversies or protests must be brought up during the driver's meeting.

8. All airbags, glass, plastic, bumper covers, rear speakers, wheel weights, and interior must be removed before arriving to the event.

9. Any aftermarket parts must be approved by Junk It. You must text and submit pictures for approval. Parts that are not preapproved before show will not be allowed.

10. No painting of the frames, inside of the car, underneath of the car, or inside of the trunk. If you do the car will not even be inspected. No refunds!!!!

11. Any patching or rust repair will only be allowed if preapproved in a text with pictures.

12. Official's decisions are final.

13. You have 1 minute to make an aggressive hit. After 1 minute that car is disqualified. Don't argue or ignore the officials to try to have more time. Once your time is up, the call goes over the radio to write you down as out, even if you still have a stick. Officials may reward more time to a person putting on a show and making big hits.

14. You are allowed 2 fires. The second time your vehicle catches fire will result in a disqualification.

15. No sandbagging, teaming, or holding. We will stop the show and break your stick

Junk It Fullsize Class 2026

DO NOT READ ANYTHING INTO THESE RULES, JUST READ THE RULES!! If it doesn't say you can, YOU CAN'T!

Any year car is allowed unless otherwise stated within this rule. NO trucks, vans, T-top cars, hearses, four-wheel-drive (4WD), all-wheel drive (AWD), ambulances, or limousines allowed. Full frame Chrysler Imperials are allowed.

Body Preparation
⦁ All vehicles must run a hood and mounted in stock location. Hood sheet metal must stay over top of fans.
⦁ Hoods will be opened for inspection. Do not secure hood until after you pass inspection!
⦁ Hood must have a minimum 12”x 12” access hole for inspection and safety. (10) total 3/8” maximum bolts, nuts, and store bought washers may be used to bolt inner and outer hood sheet metal together.
⦁ Trunk lids must have (2) 6” x 6” minimum access holes for inspection. Each hole may use (5) total 3/8” maximum bolts, nuts, and store bought washers to bolt inner and outer trunk lid sheet metal together around inspection holes (10) bolts total on the trunk lid.
⦁ Sunroofs must be covered, no exceptions.
⦁ Shaping/pre-bending/creasing trunk lid is allowed. Shaping/pre-bending/creasing of rear quarters is allowed. Absolutely no wedging trunk.
⦁ No "sedagons" fresh or pre-ran. You may only crease the front fenders & rear quarter panels, but not wedge them. Quarter panels must remain upright and may not be doubled in any way.
⦁ Drawing in the lower rear quarter panel is allowed, this material may NOT be folded or lapped past the outside edge of the frame rail it may not be pulled in past the frame rails and layered or folded on top/over onto itself.
⦁ Trunk lids may be dished. The front inside portion of the speaker deck must remain vertical. Rear quarter/trunk wedging to be measured at the furthest rear body mount. From the top of the frame rail at the body mount to the top of the rear quarter panel and/or trunk lid can be no less than 12".
⦁ Absolutely NO rust repair to the body unless it is strictly inside the drivers compartment area. (This must be approved, photos of rusted areas will be required BEFORE repairs are made!)
⦁ Hoods may be secured in (6) locations maximum, sheet metal to sheet metal only. A combination of (6) securing locations total using these options: Option 1) 1. Hoods may use (2) 1" maximum bolts/threaded rods to secure front of hood down. These locations may also replace front core support body mounts and extend up through the hood to secure. (See also Frame & Bumpers Rules for more information). 2. (1) 6" x 3/8" maximum washer may be used on top of hood per side at the core support mount location. Do not get excessive with welding or bolting! If using this method you may only use (4) additional securing locations on the hood. Bolts/threaded rod count as (2) securing locations of (6) total. Option 2) - Double strand #9 wire, seat belt, cable, or 3/8" maximum chain may be used. Securing locations may not wrap around or tie into frame rails or suspension in any way. Sheet metal to sheet metal only. Option 3) - 2" long, 2" x 2" x 1/4" angle iron may be welded to sheet metal only. Angle iron to be used in matching pairs to secure hood. Angle iron may have (1) 1/2" maximum bolts with store bought washers per angle iron matching pair.
⦁ Trunk lids and tailgates may be secured shut in (8) locations maximum using double strand #9 wire, seat belt, cable, 3/8" chain, bolts, or welded (4"x4" plates). A combination of securing techniques is allowed. This must be sheet metal to sheet metal securing only, and may not wrap around or tie into frame in any way.
⦁ If bolting trunk lid down, (1) 1/2" maximum bolt per location may be used through the quarter panel drip ledge/rail to secure trunk lid. A maximum of 4" x 4" x 1/4" washers may be used per securing location.
⦁ If trunk lid is welded down, a maximum of (8) 4" x 4" x 1/4" plates may be used, sheet metal to sheet metal only. (These plates may not be cut into pieces). ⦁ If the speaker deck is removed, (2) securing locations may be used at the wheel tub/package tray area to secure trunk lid down. ⦁ Station Wagons ONLY: If you remove your tailgate may have (6) places of #9 wire 2 strands max, must be behind axle, sheet metal to sheet metal only, roof to floor. Pillars must remain intact and on the car at all times.
⦁ Driver’s door may be welded solid. Remaining doors may be secured using (1) option: Option 1) - Excluding driver's door, all other doors may be welded 5”on, 5” off, on vertical seams only with 3” x 1/8" maximum material. If welding, no other securing methods may be used. Any excess door plate or weld will be completely removed. Option 2) - Excluding driver's door, all other doors may use (10) locations of #9 wire, seat belt, cable, or chain anywhere per door to secure. These securing locations must not secure to/route around any part of cage or frame. Securing must be sheet metal to sheet metal only. If securing doors with this option, no welding on doors is permitted.
⦁ A 1/4” maximum driver's door skin is allowed and may be completely welded. Driver's door skins are not to exceed a maximum of 3" past the front driver's door seam. (Door skins are highly recommended). No other doors may be plated/skinned.
⦁ The passenger front door may have a maximum 1/8” x 18” piece of strap steel, 3” past each front door seam. This plate must be centered on the door at bumper height. Welding on passenger door plate must conform to the 5" on, 5" off welding rule. This is for driver's safety only, do not get excessive!
⦁ #9 wire, chain, cable, seatbelt, or maximum of (2) pieces of 3” x 1/4” flat bar material may be used in attached on to the roof sheet metal. Any part of this must remain 5” away from any part of the drivetrain, roll cage, halo bar, or roof signs at any time. If using (2) metal straps, (2) additional straps attaching the vertical straps together, these straps may attach horizontally to vertical straps, and must retain the 5" clearance rule. The windshield area. A maximum of 3” attached to the cowl/dash sheet metal and maximum of 3”on roof ⦁No internal bracing of body panels, no doubling body panels. No interior seam welding. No added material anywhere to body or frame!
⦁ Maximum of (5) 3/8" bolts may be used in each wheel well opening, sheet metal to sheet metal only and using store bought nuts and washers only.
⦁ A 3/4" maximum size store-bought washer may be welded to sheet metal for each #9 wire/cable location. ⦁ All excess holes in firewall must be covered with a non-flammable material.

Suspension/Steering
⦁ (2) 2" x 4" x 1/4" plate may be welded per upper A-arm to frame the lock front suspension and maintain ride height. Only '03 and newer Ford cars may use the (2) plates on either the upper OR lower A-arms both plates may be used on the upper A-arm, or both on the lower Aarm, not (1) on each. All plates used to lock suspension must be welded to the A-arm to be considered an "A-arm plate".
⦁ Front shocks may be used but must be mounted in factory location, or shock must be completely removed. No solid shocks or threaded rod shocks allowed!
⦁ '03 and newer Ford cars may use a strut riser/spacer but must bolt into factory location. These risers/spacers cannot be welded into place or strengthen the frame or suspension in any way.
⦁ Bumper ride height, 26" max height and nothing lower then 14". Nothing lower then 14 fresh or preran. You cannot change tires after you have gotten a stick. we don't want any ramps for the rear of cars.
⦁ Store bought “twist-in” style spring spacers are permitted, absolutely no homemade spacers or blocks/spacers on top of the springs. Absolutely no added material inside of the coil pocket area!
⦁ Changing front or real coil springs to a stiffer OEM passenger car coil spring is permitted.
⦁ Rear coil springs may be wired in to place with double-strand #9 wire or clamped. Securing may not strengthen frame.
⦁ Locking rear suspension/ride height is allowed. It may be accomplished with (2) options: Option 1) A single 3/8" chain may be used from rearend to frame. 3" maximum chain link length. Only (1) link per side welded to the frame or hump plate. Chain must be positioned on the curved portion of the frame hump, not ahead of or behind the hump where frame flattens. No welding of any other chain links. No additional welding or material is allowed. Option 2) Maximum of (1) 1” threaded rod may be used per side from rearend to factory shock location on frame only. Threaded rod shocks may NOT be be used to pinch body and frame, sheet metal must be cut away. (2) 3”maximum diameter washers may be used on threaded rod shock mounting.
⦁ Aftermarket steering columns are allowed. 1" maximum diameter steering column shafts allowed. '03 and newer Ford cars must use a factory rack and pinion.
⦁ All suspension may be replaced but MUST be OEM passenger car or truck origin, meaning stock automotive manufactured parts (Chrysler, GM, Ford, etc) must be used. No custom, aftermarket, or homemade suspension. All suspension and steering must remain stock unless otherwise stated in rules.
⦁ A-arms may be interchanged w/ automotive OEM parts as long as there able to be bolted on. You may cut/trim to make them fit but no welding on a-arms, brackets, etc. A-arm must bolt on factory brackets of the frame, no drilling new holes or enlarging existing holes. (Example: 79-91 Ford upper A-arms being installed on a 98-02. Cut the mounting bar out and trim the edges of A-arms).

⦁ Any OEM spindles allowed! No altering, adding material, or welding to spindles. No Lift spindles
⦁ Aftermarket steering, pedals and shifters are allowed.
⦁ Leaf springs Cars: Maximum of (7) leaf springs per pack, 2 packs per car. Leaf spring cars will have 2 options:

Option 1) (1) 10”x6” hump plate allowed. 2) If NOT using hump plates, You may flip every other leaf to create a flat leaf pack.

You can have a total of 6 leaf spring clamps per car. All in the front or rear or all on one side your choice. Clamps can not be any bigger than 2x4x1/4 and nothing bigger then 3/8 bolts to pinch them together. Total of 6 (six) all other will be removed.
⦁ Any OEM Tie-rod may be reinforced with (1) of these options: Option 1) Stock sleeve may be replaced with a maximum of 1" OD pipe/solid tapped rod and must use a stock-type tie-rod end. Option 2) Factory adjustment sleeve and tie-rod ends may be welded and reinforced with steel. Tie-rod must have stock-type ends. A store bought washer maybe placed over the seam of the tierod and welded.
⦁ Aftermaket rear trailing arms are allowed. Solid rear trailing arms are allowed. Maximum of 2" x 3" tube that is no longer than factory rear trailing arms.
⦁ '98 and up watts-links conversion - UPPER BRACKET conversion will be allowed ONLY in the following way: Upper trailing arm brackets must be bolted in. They must be (2) separate brackets with maximum of 6”x 12”x 3/8” thick max with (5) 5/8 bolts, nuts and store bought washers per bracket. (4 corner bolts and 1 center bolt in upper bracket).
⦁ Upper brackets may only be bolted to frame package tray area above rear axle and bolts may not go through or attach to body or be attached to gas tank protector / these are not to strengthen any other part of the car. No welding to upper brackets/mounts.
⦁ ‘98 and up watts-links conversion - LOWER BRACKET will be allowed ONLY in the following way: (1) piece of 3” square tube 3”x 3”x 3/8” maximum per side of frame may be used to build the bracket or similar dimension aftermarket lower bracket. It must be attached with a 1/2" weld bead maximum to the inboard of the frame at the point where trailing arms are mounted. Drill a hole through the tube and through (1) thickness/layer of the frame (inboard side). Lower control arm must be bolted into place. No other bolts will be allowed to mount this bracket. No factory mounting brackets will be allowed to mount the trailing arms. No "pocketing" or "pinning" lower bracket through to the outboard side of frame. If using watts-links suspension conversion, factory brackets must be trimmed off the frame. If you do the conversion the factory brackets and hardware have to be completely removed. You cannot have the factory suspension and the conversion as well one or the other.
⦁ Upper and lower ball joints must be OEM no aftermarket. You may use screw in style ball joints and may weld the sleeve in factory location. The sleeve cannot be any taller than 2 inches tall and can only be welded to the a-frame. No ball joint protectors at all will be allowed to run.
⦁ Sway bar may be used but must use OEM for your make and model and use OEM mounts on bottom of frame. Sway bar may be bent and bolted down directly to lower A-arms. Sway bar may not be attached or welded to any other part of frame, suspension, or drivetrain. Only 03 and newer can bolt sway bar to upper or lower a-arms, everyone else can only bolt to lower.

Brakes & Tires
⦁ Vehicle must have working brakes at all times and have the ability to stop.
⦁ Any tire/rim combo is allowed. No tires taller than 30".
⦁ Bead locks/bead protectors are allowed.
⦁ (4) wheels max per vehicle, no dual tires.
⦁ No split rims or studded tires. Solid and foam filled tires allowed.
⦁ Wheel weights must be removed.
⦁ Tubes and outer tire flaps/skins are allowed.
⦁ Valve stem protectors are allowed but must be deemed safe.

Frame & Bumpers

ALL Frames must be same year when reclipping, You are not allowed to put a ford 2011 rear on a 03 and newer or a 03 and new front on a 98-02 you will not run.

⦁Frame and body must match gm to gm /ford to ford. (Example: 03 and newer fords may swap body to 80's style fords) If using a convertible frame, it must be used under a convertible body, a same generation/era car hardtop must be welded on.
⦁ Frame shaping, contouring, forming, or folding is NOT allowed with the exception the rear frame reliefs/notches to achieve the rear of the car to roll/pack.
⦁ NO welding, bolting, wiring or adding any material/substance to strengthen frames. - At Inspectors discretion, frames will be drilled, ground on, or wiped down. Absolutely NO painting or spraying any material on/in frames or welds. Any excess frame welding will result in COMPLETLEY REMOVING the added weld or material, or forfeiting to participate. All fix it plates must remain bare metal if you paint them, you do not run.
⦁ You may tilt frames in front only, (do not tilt the rear) no adding metal when this is done. 79-02 fords can cut flaps tilt and reweld. all others may slice frame tilt and welded back together. DO NOT over-weld or abuse this rule! Absolutely no added material to achieve frame tilt. ⦁ “Cold-bending” frame is allowed. No other tilting/tipping allowed to the car anywhere.
⦁ Maximum of 6” tall core support spacers using 3” x 3” x 1/4" maximum material. Maximum of 1” threaded rod may be used from bottom of frame up through core support and used to secure hood down. 3” x 1/4” maximum washer used on rod below the frame, and a 6” x 3/8” maximum washer on top of the hood. Absolutely no welding of core support spacer, threaded rod, or washers to the frame.
⦁ Using (1) method of body mount options is allowed: Option 1) If all the body mounts are left stock, (4) total body mount bolts using 3/4” maximum threaded rod may be added. Added mounts may pass through (2) layers of the body maximum, using pre-existing frame holes or mounted to the side of the frame. Added mounts may only be installed vertically and not be attached into any part of the cage. Added mount bolts/threaded rod may be 14” long maximum. (2) 3” x 3” x 1/4” maximum diameter washers may be used at added mounts. These washers may not be welded in any way. Broken/rusted-out OEM body mount bolts may be replaced with factory length 3/8” bolts with 3/8” store-bought washers. You must drill out the factory bushing and still use it in the factory position if repairing an broken/rusted-out OEM body mount bolt. Added mounts must still maintain a 1” space between body and frame. Option 2) If body mounts are changed, maximum 5/8”x 6” bolts may be used. 3” diameter maximum body mount spacers may be used to space body from frame, these spacers must maintain a minimum of 1” space between the body and the frame. The body mounts may only go through one layer of the body with the exception of (2) in the trunk which are allowed to go vertically up through the trunk lid and (2) at the core support that may go up through the hood. Maximum of (4) washers and (4) nuts at each core support and trunk mount. Maximum of (2) washers and (2) nuts each on all other body mounts. Washers to not exceed 3” x 3” x 1/4” and the bottom washer must remain inside the frame. All body mount washers must be “free-floating” and not welded to body or frame.

All Sub Frame Cars can add 2 extra body mounts in the trunk area. These must stay in the trunk area and can be welded down the side of the frame. Straight up and down do not x these or try anything else or you will lose these body mounts. No more then 4 inches of weld on the frame. 3/4 max all thread can be used.
⦁ Absolutely no welding in body mount locations on the frame, this may result in body mount removal and/or disqualification.
⦁ Bumpers may be welded to end of frame rail. Bumpers may be “hard-nosed” to end of frame. No shortening of rear frame rails. Bumper shocks must match make/model of the car. Shocks may be collapsed or pushed into frame and welded. Shocks may be plug-welded to the frame no further back than 8” from the back of the bumper.
⦁ Front frames may be shortened no further back than the front of the core support body mount hole. No moving or relocating the core support mount or mount bracket.

⦁ Homemade, aftermarket/replica, or loaded OEM bumpers allowed. NO DIGGER OR FLIPPER bumpers are allowed, If you show up with one you will cut it off or load! Bumpers cannot have sharp or protruding edges. Points may be no further than a OEM Chrysler New Yorker “Pointy” front bumper.
⦁ Front and rear bumper bracket/plate options - All bumper shocks or bumper brackets must be OEM brackets/shocks to proper make/model of car and must stay in factory position. OEM brackets may be continuously welded from front of the bracket back 8” maximum. No additional welding allowed past 8”. Cars equipped with shocks may collapse shocks and weld. Brackets and shocks may be welded to bumper. If car does not come with or you choose to remove factory bumper shocks or bumper brackets you may use 8" x 4" x 1/4” plate as a bracket. This goes for front and back, these plates must be welded to the out side of the frame and must touch bumper. 2 in the front, (one per driver side and one per passenger's side) 2 in the rear (one per driver side and one per passenger's side) these will not be counted as fix it plates. If using these homemade brackets all factory shocks and brackets must be removed.

⦁ Front bumper brackets on the front of the car, rear bumper brackets on the rear of the car no swapping.
⦁ (2) pieces of 3/8" maximum chain per side may be BOLTED from the frame/bracket to the bumper, this is only to keep the bumper from completely falling off. Maximum of 3" chain link length.
⦁ Hump plates may either be straight across or contoured, not both! 1/2" weld bead maximum. If using “Tee-Pee” plates, they will be measured before manipulation. All hump plates must be installed on the outboard side of the frame (outside toward tires). Hump plates must be a minimum of 3" away from rear axle/brackets at all times. Hump plate may NOT be attached to the body or drivetrain in any way.

Leaf Spring cars = 10x6x1/4 hump plate or can flat leaf,

77 and New GM's = 30x6x1/4 hump plate

All others can have = 22x6x1/4 hump plate
⦁ Fresh Cars get Two - 4" x 6" x 1/4 ”or 5” x 5”x 1/4”. Fix it plates
⦁ Pre-ran cars will be allowed a maximum of (6) Fix it plates 4" x 6" x 1/4 ”or 5” x 5”x 1/4”. Plates will not be allowed to be cut apart or manipulated into different shapes or dimensions, they must fit measurement criteria with 90-degree square edges.
⦁ "Fix-It-Plates" must be welded to frame only, do not attach to body, driveline, or cage in any way! 1/2" weld bead maximum on all "Fit-It-Plates".

Drivetrain
⦁ Any engine/transmission combo allowed. Engine swaps are allowed. (Example: Chevy engine/transmission in a Ford car). Swapping from fuel injection to a carburetor is allowed.
⦁ OEM or aftermarket engine mounts are allowed. Any type of mount used must have a bolt going through a rubber bushing. Mounting area 8" x 8" maximum in factory position. No solid or fully welded mounts allowed, do not abuse this rule. Mounts cannot strengthen car. ⦁ (1) 3/8” maximum chain per side of engine as a "hold-down" may be used. Maximum of (2) links per chain welded to the engine cradle/saddle only (not to side rails) with a 1/2” wide weld bead maximum. 3" maximum chain link length.
⦁ A steel or aluminum bell housing and a transmission brace is allowed. No part of the brace may be more than 4” wider, taller, or longer than the transmission. Transmission brace may attach to the single lowest bolt on the rear of each cylinder head ONLY. Transmission brace may not attach in any other way, do not abuse this rule!
⦁ There MUST be a 1" space between the transmission/transmission brace and the crossmember. No welding of the 1" transmission mount/spacer to crossmember, transmission, or transmission brace. 1" space must be rubber, neoprene, or similar material to act as a mount and may be bolted into place.
⦁ An OEM crossmember and mount or 2” x 2” x 1/4” tube maximum crossmember may be used. A 4” x 4” x 1/4” crossmember mounting pad may be welded to the frame with 1/2” weld bead maximum.
⦁ A basic front plate and lower engine cradle is allowed. Lower cradle may not be above the cylinder heads of the engine. Front pulley protector is allowed. Cradle may not go further back than 4” past the 8” engine mounting pad location. This cannot connect to midplate.
⦁ No distributor protectors allowed.
⦁ A carburetor protector is allowed but must not extend further back than 16" measured from the front of the engine block. Carburetor protector may only attach straight down to the intake bolts and may not be attached to transmission brace, bell housing, or adapter/midplate in any way. If carburetor protector is past specified point, firewall will be cut out to 5” past the widest parts of the engine.
⦁ A “BOP-Style” adapter/midplate is allowed but must not extend past edge of transmission bell housing 2” in any direction. This cannot connect to the lower cradle. Do not abuse this rule!

⦁ A fan shroud will be allowed but must be constructed of non-flammable, flexible material. No steel or engine/cradle mounted fan shrouds. Fan shroud can not strengthen the car in any way! ⦁ Any rear differential allowed. Welded and locked differentials are allowed.
⦁ Rearend braces will be allowed. Rear end brace must be a minimum of 5” away from any part of the frame on fresh or pre-ran cars. Pinion brakes are allowed.
⦁ Stock type or slider driveshafts allowed.
⦁ Exhaust must exit straight down under vehicle past the drivers seat, or straight up through the hood.
⦁ Aftermarket shifters and brake/gas pedals are allowed.
⦁ Radiator must mount in factory location or be removed.
⦁ No homemade radiators allowed. Overflow tanks are allowed inside the engine compartment only.
⦁ Radiator protectors are allowed. Protectors may be 1/8" maximum flat material and no wider than 1” past the factory core support radiator opening. When mounting radiator protector only (1) option is allowed: Option 1) - A total of 12" of weld can be used to secure radiator protector. No bolting is allowed if this method is used. Option 2) - (10) 5/16" bolts may be used to secure radiator protector. Store bought nuts and washers only. No welding is allowed if this method is used.
⦁ Radiators can be spray foamed in place.
⦁ Electrical fans are allowed.
⦁ ‘03 and newer Ford cars may run a manufactured aftermarket bolt-in style engine cradle. Aftermarket cradle may not strengthen or alter the factory steering or aluminum OEM cradle. (Example: 03 Nation, Cory Budde Design, etc -). These may NOT be welded in, “Fix-It-Plates” may also not attach or weld to aftermarket cradle, no exceptions. Driver’s Compartment
⦁ Drivers door MUST be padded.
⦁ A 4-point cage is allowed. Door Bar length front to back is 60”. 4” x 4” x 1/4” or equivalent maximum material allowed (Example: 2" x 6" rectangle tubing). Only door bars may be a maximum of 10” x 2” material. Cage must stay within the driver's compartment. Center bar or gussets are allowed but must be withing main cage. All parts of cage must stay a minimum of 6” from the floor.

⦁ You have a choice to weld 2 down legs to the top side of the frame. Either 2 in the front or 2 in the back not both. You cannot weld one in the front and one in the back, Both have to be in the same area. The down legs that you weld to the top of the frame can be no bigger than 2x3x1/4. These two down legs must be on top of the frame not down the side or inside of the frame. Bars must be vertical only.
⦁ Any part of cage must be a minimum of 4” from the transmission tunnel or transmission brace.
⦁ A rollover bar is required. This includes (2) vertical upright bars and a bar over the roof of vehicle to attach the upright bars. All rollover bars must be welded to the bar behind seat and/or the rear of door bars. Upright bars cannot extend down to floor of vehicle unless you are choosing to have rear down legs.

⦁ (2) 4” x 4” x 4” maximum plates, angle iron, or tubes may be welded to top roof bar. These “tabs” allows for the roof bar to be bolted to the roof sheet metal in (1) place per side of the car. Each “tab” may be attached using (1) 1/2” bolt and store-bought nuts and washers per side, no welding. Upright bars and roof bar cannot be attached to any other part of the car or cage. ⦁ An approved fuel tank/cell must be securely fastened to rear driver's compartment floor metal using bolts or in a tray/holder attached from the cage.
⦁ (4) locations of double-strand #9 wire or 3/8" maximum cable may attach cage to frame anywhere within the driver's compartment of the vehicle. No other wire, cable, or chain allowed.
⦁ A fuel tank tray/protector may be used. Fuel tank tray/protector must attached to main cage and be no wider than 32”. Tank tray/protector may contact rear sheet metal but cannot be attached. Bars behind fuel tank must be vertically straight up only, and may not angle toward back of the vehicle. Fuel tank protector may not extend further than 10” above fuel tank. Station wagons ONLY - Fuel tank tray/protector may not extend further back than a straight line across the front of the rear inner wheel wells. Do not abuse this rule.
⦁ All fuel lines inside driver's compartment must be approved steel or braided lines and routed to prevent being cut or pinched. High pressure lines and proper fittings recommended. Officials must deem safe.
⦁ Transmission coolers are allowed inside the vehicle. Transmission coolers must use approved high pressure lines and proper connections. Officials must deem safe.
⦁ (2) Automotive-type battery(s) maximum allowed. Battery must be relocated to front passenger seat area, front floorboard area, or mounted in a steel tray on cage away from doors. Battery(s) must be securely fastened and covered.
⦁ If using an electric fuel pump, “On/Off” switch or wires must be CLEARLY labeled for officials and safety in case of fire or rollover.
**Simple rules, simple build, keep it that way. Again, do not get "creative" or read into these rules. If it is not clearly described above, it is not allowed. If it doesn't say you can, YOU CAN'T! Again, If you have any questions, please Text Nate Burgess 765-744-5524You only get 2 chances to pass inspection, If you get sent back to correct something on your car and it does not meet our standards when you come back to tech you will not run that night. If it doesn’t say you can do it, don’t do it. Shows must start on time and we will not be playing the cat and mouse games anymore. Any controversies or protests must be brought up during the drivers meeting. We have the right to reinspect, cut, or drill any car at any time. If you are caught breaking the rules, you will forfeit all winnings and or prizes you are due. No sandbagging, teaming, or holding. You cannot pin to win. Any of these will result in a disqualification. Any questions, CALL FIRST. Don’t assume anything. The Official's decision is final